Menu

Repairing Harvest Ruts This Spring

I’ve seen more fields with harvest ruts this year than I usually do. There were several weather-related factors that contributed to this situation. The wet spring led to planting delays, delaying crop maturity. However, the biggest factor was the green stems that were prevalent throughout much of Michigan. The green stems were a physiological response to the dry weather we experienced in June and most of July, and the abundant rain occurring in August and September. The stems also stayed green for an extended period of time because a killing frost didn’t occur until late November.

Producers don’t like harvesting soybeans with green stems as it is more difficult, slow and plugging the cylinder or rotors in the combine is a possibility. Producers that waited for the green stems to dry down missed out on some ideal harvest conditions and ended up harvesting some of their fields when the soil was too wet. As a result, harvest equipment left ruts in these fields. In some cases, the ruts are more than 6 inches deep and in others, they are less than 2 inches deep. Most of the harvest ruts I’ve seen are confined to localized areas within fields. However, in a few cases, deep ruts created by every pass of the combine can be seen (see photo). All ruts deeper than your projected planting depth must be leveled prior to planting for planters and drills to perform properly.

When repairing ruts this spring, the objectives are to fill and level the ruts just enough to facilitate planting operations without causing further soil compaction. Loosening the soil at the bottom of or below the ruts should not be attempted because the tillage tools will need to be operated at greater depths and into soil that is probably too wet. This increases the risk of further soil smearing or compaction to occur. Root growth and crop yields will be reduced in the repaired areas.

Michigan State University Extension recommends secondary tillage implements such as disks, field cultivators, soil finishers and vertical tillage for repairing ruts 2-4 inches deep. For ruts deeper than 4 inches, a chisel plow may be necessary. Always operate the implements as shallow as possible to fill and level the ruts. Multiple passes may be required to achieve the desired degree of leveling.

Perform tillage operations when the soil at or just above the operating depth is dry enough to prevent soil smearing and compaction. Iowa State University agricultural engineer Mark Hanna recommends the following methods for assessing soil moisture conditions:

  • Collect a handful of soil from an area between ruts and 2 inches above the operating depth of the tillage tool and form it into a ball. Then throw the ball of soil as if throwing a runner out at first base. If the ball stays mostly intact until it hits the ground, the soil is too wet to till.
  • Take a similar soil sample in your hand and squeeze the soil in your fist and use your thumb and forefinger to form a ribbon of soil. If the ribbon extends beyond 2-3 inches before breaking off, the soil is too wet to till.

Remember, your objectives with spring rut repairs are to fill and level the ruts without causing further soil compaction. Attempting to loosen the soil below the ruts increases the potential for further soil smearing and compaction to occur.

Source: Mike Staton, Michigan State University Extension 

Recent News

Fall-applied Herbicides-What Goes Around Comes Around
9/22/2020

Fall herbicide treatments have fallen off over the past several years for a couple of reasons, among them the effectiveness of new soybean trait systems for managing marestail, some generally crappy weather in late fall, and efforts to reduce input costs.  We are seeing a resurgence in some weeds, such as dandelion, which respond well […]

New Round of Farm Aid for COVID Losses Announced, and Causes Snag in Congressional Spending Bill
9/22/2020

Andrew Restuccia and Jesse Newman reported in Friday’s Wall Street Journal that, “President Trump unveiled $13 billion in new aid to farmers facing economic harm from the coronavirus pandemic as he aimed to boost support among rural voters at a campaign rally. ‘I’m proud to announce that I’m doing even more to support Wisconsin farmers,’ said Mr. Trump, speaking outside […]

Corn Silage Needs Adequate Moisture to Ferment
9/18/2020

Early season frost is challenging for corn silage producers, according to Karl Hoppe, Extension livestock systems specialist at NDSU’s Carrington Research Extension Center. Frost makes an abrupt end to the corn-growing season. This begins the dry-down period for the corn plants. “Good corn silage fermentation requires adequate moisture to reduce dry-matter loss and spoilage,” Hoppe […]

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now